View HCS240MS_338993.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HCS240MS
September 1995
Radiation Hardened Octal Buffer/Line Driver, Three-State
Pinouts
20 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE (SBDIP) MIL-STD-1835 CDIP2-T20, LEAD FINISH C TOP VIEW
AE AI1 BO4 AI2 BO3 AI3 BO2 AI4 BO1 1 2 3 4 5 6 7 8 9 20 VCC 19 BE 18 AO1 17 BI4 16 AO2 15 BI3 14 AO3 13 BI2 12 AO4 11 BI1
Features
* 3 Micron Radiation Hardened CMOS SOS * Total Dose 200K RAD (Si) * SEP Effective LET No Upsets: >100 MEV-cm2/mg * Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/ Bit-Day (Typ) * Dose Rate Survivability: >1 x 1012 RAD (Si)/s * Dose Rate Upset >10
10
RAD (Si)/s 20ns Pulse
* Latch-Up Free Under Any Conditions * Military Temperature Range: -55oC to +125oC * Significant Power Reduction Compared to LSTTL ICs * DC Operating Voltage Range: 4.5V to 5.5V * Input Logic Levels - VIL = 30% of VCC Max - VIH = 70% of VCC Min * Input Current Levels Ii 5A at VOL, VOH
GND 10
Description
The Intersil HCS240MS is a Radiation Hardened Inverting Octal Buffer/Line Driver, Three-State, with two active-low output enables. The HCS240MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. The HCS240MS is supplied in a 20 lead Ceramic flatpack (K suffix) or a SBDIP Package (D suffix).
AE AI1 BO4 AI2 BO3 AI3 BO2 AI4 BO1 GND
20 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE (FLATPACK) MIL-STD-1835 CDFP4-F20, LEAD FINISH C TOP VIEW
1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCC BE AO1 BI4 AO2 BI3 AO3 BI2 AO4 BI1
Ordering Information
PART NUMBER HCS240DMSR HCS240KMSR HCS240D/Sample HCS240K/Sample HCS240HMSR TEMPERATURE RANGE -55oC to +125oC -55oC to +125oC +25oC +25oC +25oC SCREENING LEVEL Intersil Class S Equivalent Intersil Class S Equivalent Sample Sample Die PACKAGE 20 Lead SBDIP 20 Lead Ceramic Flatpack 20 Lead SBDIP 20 Lead Ceramic Flatpack Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright (c) Intersil Corporation 1999
Spec Number File Number
1
518837 3562.1
HCS240MS Functional Diagram
AO1 18 AO2 16 AO3 14 AO4 12 BO1 9 BO2 7 BO3 5 BO4 3
N
P
N
P
N
P
N
P
P
N
P
N
P
N
P
N
1 AE
2 AI1
4 AI2
6 AI3
8 AI4
11 BI1
13 BI2
15 BI3
17 BI4
19 BE
TRUTH TABLE INPUTS AE, BE L L H An L H X OUTPUT Yn H L Z
H = High Voltage Level, L =Low Voltage Level X = Immaterial, Z =High Impedance
Spec Number 2
518837
Specifications HCS240MS
Absolute Maximum Ratings
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7.0V Input Voltage Range, All Inputs . . . . . . . . . . . . .-0.5V to VCC +0.5V DC Input Current, Any One Input . . . . . . . . . . . . . . . . . . . . . . . .10mA DC Drain Current, Any One Output. . . . . . . . . . . . . . . . . . . . . . .35mA Storage Temperature Range (TSTG) . . . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10sec) . . . . . . . . . . . . . . . . . . +265oC Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 (All Voltage Reference to the VSS Terminal)
Reliability Information
Thermal Resistance JA JC SBDIP Package. . . . . . . . . . . . . . . . . . . . 72oC/W 24oC/W Ceramic Flatpack Package . . . . . . . . . . . 107oC/W 28oC/W Maximum Package Power Dissipation at +125oC Ambient SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.69W Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . . . . 0.47W If device power exceeds package dissipation capability, provide heat sinking or derate linearly at the following rate: SBDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9mW/oC Ceramic Flatpack Package . . . . . . . . . . . . . . . . . . . . . . 9.3mW/oC Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Gates
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +4.5V to +5.5V Input Rise and Fall Time at 4.5V VCC (tr, tf) . . . . . . . 100ns/V Max. Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . VCC to 70% of VCC Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . .0V to 30% of VCC
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP A SUBGROUPS 1 2, 3 Output Current (Source) IOH VCC = 4.5V, VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0V, (Note 2) VCC = 4.5V, VIH = 4.5V, VOUT = 0.4V, VIL = 0V, (Note 2) VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOH = -50A VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = -50A Output Voltage Low VOL VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOL = 50A VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOL = 50A Input Leakage Current Three-State Output Leakage Current Noise Immunity Functional Test IIN VCC = 5.5V, VIN = VCC or GND VCC = 5.5V, Force Voltage = 0V or VCC VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, (Note 3) 1 2, 3 1 2, 3 1, 2, 3 LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC MIN -7.2 -6.0 7.2 6.0 VCC -0.1 VCC -0.1 MAX 40 750 UNITS A A mA mA mA mA V
PARAMETER Supply Current
SYMBOL ICC
(NOTE 1) CONDITIONS VCC = 5.5V, VIN = VCC or GND
Output Current (Sink)
IOL
Output Voltage High
VOH
+25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC, +125oC, -55oC
1, 2, 3
-
V
1, 2, 3
0.1
V
1, 2, 3
-
0.1 0.5 5.0 1 50 -
V A A A A V
1 2, 3
-
IOZ
1 2, 3
FN
7, 8A, 8B
NOTES: 1. All voltages reference to device GND. 2. Force/Measure functions may be interchanged. 3. For functional tests, VO 4.0V is recognized as a logic "1", and VO 0.5V is recognized as a logic "0".
Spec Number 3
518837
Specifications HCS240MS
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP A SUBGROUPS 9 10, 11 Propagation Delay TPLH1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 9 10, 11 Propagation Delay TPZL1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 9 10, 11 Propagation Delay TPLZ1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 9 10, 11 Propagation Delay TPZH1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 9 10, 11 Propagation Delay TPHZ1 VCC = 4.5V, VIH = 4.5V, VIL = 0V 9 10, 11 NOTES: 1. All voltages referenced to device GND. 2. AC measurements assume RL = 500, CL = 50pF, Input TR = TF = 3ns. LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC MIN 2 2 2 2 2 2 2 2 2 2 2 2 MAX 18 20 19 21 22 25 21 23 20 22 20 21 UNITS ns ns ns ns ns ns ns ns ns ns ns ns
PARAMETER Propagation Delay
SYMBOL TPHL1
(NOTES 1, 2) CONDITIONS VCC = 4.5V, VIH = 4.5V, VIL = 0V
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER Capacitance Power Dissipation SYMBOL CPD (NOTE 1) CONDITIONS VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz TEMPERATURE +25oC +125oC, -55oC Input Capacitance CIN VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz +25oC +125oC, -55oC Output Capacitance COUT VCC = 5.0V, VIH = 5.0V, VIL = 0V, f = 1MHz +25oC +125oC, -55oC Output Transition Time TTHL TTLH VCC = 4.5V, VIH = 4.5V, VIL = 0V +25oC +125oC, -55oC NOTE: 1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. MIN 1 1 MAX 56 86 10 10 20 20 15 22 UNITS pF pF pF pF pF pF ns ns
Spec Number 4
518837
Specifications HCS240MS
TABLE 4. POST IRRADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS 200K RAD LIMITS PARAMETER Supply Current Output Current (Source) Output Current (Sink) SYMBOL ICC IOH (NOTE 1) CONDITIONS VCC = 5.5V, VIN = VCC or GND VCC = VIH = 4.5V, VOUT = VCC -0.4V, VIL = 0 VCC = VIH = 4.5V, VOUT = 0.4V, VIL = 0 VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOH = -50A VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOH = -50A Output Voltage Low VOL VCC = 5.5V, VIH = 3.85V, VIL = 1.65V, IOL = 50A VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, IOL = 50A Input Leakage Current Three-State Output Leakage Current Noise Immunity Functional Test Propagation Delay IIN IOZ VCC = 5.5V, VIN = VCC or GND VCC = 5.5V, Force Voltage = 0V or VCC TEMPERATURE +25oC +25oC MIN -6.0 MAX 0.75 UNITS mA mA
IOL
+25oC
6.0
-
mA
Output Voltage High
VOH
+25oC
VCC -0.1 VCC -0.1 -
-
V
+25oC
-
V
+25oC
0.1
V
+25oC
-
0.1
V
+25oC +25oC
-
5 50
A A
FN
VCC = 4.5V, VIH = 3.15V, VIL = 1.35V, (Note 2) VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V VCC = 4.5V, VIH = 4.5V, VIL = 0V
+25oC
-
-
V
TPHL1
+25oC
2
20
ns
Propagation Delay
TPLH1
+25oC
2
21
ns
Propagation Delay
TPZL1
+25oC
2
25
ns
Propagation Delay
TPLZ1
+25oC
2
23
ns
Propagation Delay
TPZH1
+25oC
2
22
ns
Propagation Delay
TPHZ1
+25oC
2
21
ns
NOTES: 1. All voltages referenced to device GND. 2. For functional tests, VO 4.0V is recognized as a logic "1", and VO 0.5V is recognized as a logic "0".
TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC) GROUP B SUBGROUP 5 5 5
PARAMETER ICC IOL/IOH IOZ
DELTA LIMIT 12A -15% of 0 Hour 200nA
Spec Number 5
518837
Specifications HCS240MS
TABLE 6. APPLICABLE SUBGROUPS CONFORMANCE GROUPS Initial Test (Preburn-In) Interim Test I (Postburn-In) Interim Test II (Postburn-In) PDA Interim Test III (Postburn-In) PDA Final Test Group A (Note 1) Group B Subgroup B-5 Subgroup B-6 Group D NOTE: 1. Alternate group A testing in accordance with Method 5005 of Mil-Std-883 may be exercised. METHOD 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 100%/5004 Sample/5005 Sample/5005 Sample/5005 Sample/5005 GROUP A SUBGROUPS 1, 7, 9 1, 7, 9 1, 7, 9 1, 7, 9, Deltas 1, 7, 9 1, 7, 9, Deltas 2, 3, 8A, 8B, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11 1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas 1, 7, 9 1, 7, 9 Subgroups 1, 2, 3, 9, 10, 11 ICC, IOL/H, IOZL/H READ AND RECORD ICC, IOL/H, IOZL/H ICC, IOL/H, IOZL/H ICC, IOL/H, IOZL/H
TABLE 7. TOTAL DOSE IRRADIATION CONFORMANCE GROUPS Group E Subgroup 2 NOTE: 1. Except FN test which will be performed 100% go/no-go. TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS OSCILLATOR OPEN STATIC I BURN-IN (Note 1) 3, 5, 7, 9, 12, 14, 16, 18 STATIC II BURN-IN (Note 1) 3, 5, 7, 9, 12, 14, 16, 18 DYNAMIC BURN-IN (Note 2) NOTES: 1. Each pin except VCC and GND will have a series resistor of 10k 5%. 2. Each pin except VCC and GND will have a series resistor of 680 5%. 1, 10, 19 3, 5, 7, 9, 12, 14, 16, 18 20 2, 4, 6, 8, 11, 13, 15, 17 10 1, 2, 4, 6, 8, 11, 13, 15, 17, 19, 20 1, 2, 4, 6, 8, 10, 11, 13, 15, 17, 19 20 GROUND 1/2 VCC = 3V 0.5V VCC = 6V 0.5V 50kHz 25kHz TEST METHOD 5005 PRE RAD 1, 7, 9 POST RAD Table 4 READ AND RECORD PRE RAD 1, 9 POST RAD Table 4 (Note 1)
TABLE 9. IRRADIATION TEST CONNECTIONS OPEN 3, 5, 7, 9, 12, 14, 16, 18 GROUND 10 VCC = 5V 0.5V 1, 2, 4, 6, 8, 11, 13, 15, 17, 19, 20
NOTE: Each pin except VCC and GND will have a resistor of 47K 5% for irradiation testing. Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.
Spec Number 6
518837
HCS240MS Intersil Space Level Product Flow - `MS'
Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) GAMMA Radiation Verification (Each Wafer) Method 1019, 4 Samples/Wafer, 0 Rejects 100% Nondestructive Bond Pull, Method 2023 Sample - Wire Bond Pull Monitor, Method 2011 Sample - Die Shear Monitor, Method 2019 or 2027 100% Internal Visual Inspection, Method 2010, Condition A 100% Temperature Cycle, Method 1010, Condition C, 10 Cycles 100% Constant Acceleration, Method 2001, Condition per Method 5004 100% PIND, Method 2020, Condition A 100% External Visual 100% Serialization 100% Initial Electrical Test (T0) 100% Static Burn-In 1, Condition A or B, 24 hrs. min., +125oC min., Method 1015 100% Interim Electrical Test 1 (T1) 100% Delta Calculation (T0-T1) 100% Static Burn-In 2, Condition A or B, 24 hrs. min., +125oC min., Method 1015 100% Interim Electrical Test 2 (T2) 100% Delta Calculation (T0-T2) 100% PDA 1, Method 5004 (Notes 1and 2) 100% Dynamic Burn-In, Condition D, 240 hrs., +125oC or Equivalent, Method 1015 100% Interim Electrical Test 3 (T3) 100% Delta Calculation (T0-T3) 100% PDA 2, Method 5004 (Note 2) 100% Final Electrical Test 100% Fine/Gross Leak, Method 1014 100% Radiographic, Method 2012 (Note 3) 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 4) 100% Data Package Generation (Note 5)
NOTES: 1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1. 2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the failures from subgroup 7. 3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 5. Data Package Contents: * Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity). * Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage. * GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil. * X-Ray report and film. Includes penetrometer measurements. * Screening, Electrical, and Group A attributes (Screening attributes begin after package seal). * Lot Serial Number Sheet (Good units serial number and lot number). * Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test. * The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative.
Spec Number 7
518837
HCS240MS Propagation Delay Timing Diagram
VIH VS VSS TPLH TPHL VOH VS VOL OUTPUT CL RL CL = 50pF RL = 500 INPUT
Propagation Delay Load Circuit
DUT TEST POINT
Transition Timing Diagram
VOH TTLH 80% VOL 20% 80% 20% TTHL
OUTPUT
VOLTAGE LEVELS PARAMETER VCC VIH VS VIL GND HCS 4.50 4.50 2.25 0 0 UNITS V V V V V
Three-State High Timing Diagrams
VIH VS VSS TPZH TPHZ VOH VT VOZ OUTPUT VW INPUT
Three-State High Load Circuit
DUT TEST POINT
CL
RL
CL = 50pF RL = 500
THREE-STATE HIGH VOLTAGE LEVELS PARAMETER VCC VIH VS VT VW GND HCS 4.50 4.50 2.25 2.25 3.60 0 UNITS V V V V V V
Spec Number 8
518837
HCS240MS Three-State Low Timing Diagrams
VIH VS VSS TPZL TPLZ VOZ VT VOL CL CL = 50pF OUTPUT VW DUT TEST POINT RL INPUT
Three-State Low Load Circuit
VCC
THREE-STATE LOW VOLTAGE LEVELS PARAMETER VCC VIH VS VT VW GND HCS 4.50 4.50 2.25 2.25 0.90 0 UNITS V V V V V V
RL = 500
Spec Number 9
518837
HCS240MS Die Characteristics
DIE DIMENSIONS: 108 x 106 x 19 1mils METALLIZATION: Type: Si - Al Thickness: 11kA 1kA GLASSIVATION: Type: SiO2 Thickness: 13kA 2.6kA WORST CASE CURRENT DENSITY: <2.0 x 105 A/cm2 BOND PAD SIZE: 4 x 4 (mils) 100 x 100m
Metallization Mask Layout
HCS240MS
(20) VCC (19) BE (3)BO4 (2) AI1 (1) AE
(18) AO1
AI2 (4) (17) BI4 BO3 (5)
(16) AO2
AI3 (6) (15) BI3
BO2 (7) (14) AO3
GND (10)
AO4 (12)
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
BI2 (13)
BI1 (11)
AI4 (8)
BO1 (9)
Spec Number 10
518837

▲Up To Search▲

Price & Availability of HCS240MS

	To Download HCS240MS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .